Published date: May 06 2018

Journal Title: KnE Materials Science

Issue title: 15th International School-Conference "New Materials – Materials of Innovative Energy" (MIE)

Pages: 221–231

DOI: 10.18502/kms.v4i1.2146

M Isaenkovaisamarg@mail.ru

Y Perlovich

A Osintsev

V Fesenko

M Zaripova

Cyclic tensile tests were carried out as applied to annealed foils of the superelastic Ti-22Nb-6Zr alloy (at.%) as well as indentation of these foils with an increasing amplitude of indenter intrusion in the sample at temperatures lowering from 20∘ down to -60-70∘C. Mechanical tests were performed on samples cut along and
across the rolling direction. According to the results of measurements of mechanical properties, it is established that during cyclic stretching of foils in the rolling direction, superelasticity manifests itself, and also material training is observed with subsequent preservation of the maximal renewable deformation. When the foil is loaded in the transverse direction, no superelasticity is observed, moreover, some samples
are destroyed even with a deformation of 2%. With a decrease in the annealing temperature of foils, the curve of the continuous change of loading with the depth of indenter penetration undergoes substantial changes, which indicate the appearance of a superelastic deformation under the indenter. Curves of monotonic loading and discharge undergo an inflection, and the plastic deformation region is substantially reduced. From the discharge curves in this case, we can calculate two elastic modules, typical for the usual elasticity and superelastic behavior of the alloy. In general, the main characteristics of the continuous indentation curve depend on the amount of the martensitic phase. The dependence of the modules of elasticity for foils, cooling
down to -(60-70∘C), and for their subsequent heating up to the room temperature is constructed.

[1] Miyazaki S, Kim HY, Hosoda H Development and characterization of Ni-free Ti-base shape memory and superelastic alloys. Mater Sci Eng A 438-440, 2006. - P. 18-24.


[2] Miyazaki S, Kim HY TiNi-base and Ti-base shape memory alloys. Mater Sci Forum 561-565, 2006. - P. 5-21.


[3] Kim HY, Miyazaki S Martensitic transformation and superelastic properties of Ti-Nb base alloys. Mater Trans 56, 2015. - P. 625-634.


[4] Kim HY, Hashimoto S, Kim JI, Hosoda H, Miyazaki S Mechanical properties and shape memory behavior of Ti-Nb alloys. Mater Trans 45. - 2004. - P. 2443-2448.


[5] Kim HY, Ikehara Y, Kim JI, Hosoda H, Miyazaki S Martensitic transformation, shape memory effect and superelasticity of Ti-Nb binary alloys. Acta Mater 54, 2006. - P. 2419-2429.


[6] Fesenko, V., Perlovich Yu., Isaenkova, M. The Increased Shape Memory Effect in Rolled Ti-48%Ni-2%Fe Single Crystals // Materials Today: Proceedings. Vol. 2, 2015. - P. 751-754.


[7] Dubinskiy S., Prokoshkin S., Brailovski V. Structure of thermo-mechanical processing of Ti-Nb-Zr(Ta) alloys and manifestation of the shape-memory effect. // Physics of Metals and Metallography. - 2011. - P. 529-542.


[8] Dubinskiy S. Ti-Nb-(Zr, Ta) Superelastic alloys for medical implants: termomechanical processing, structure, phase transformations and functional properties. - Montreal: Ph.D. Thesis. - 2013. - P.4-15.


[9] Strietzel R., Hösch A., Kalbfleisch H. In vitro corrosion of titanium // Biomaterials, 1998. - 1499 p.


[10] Borodkina M., Spektor E. X-ray diffraction analysis of the texture of metals and alloys. Metallurgy, 1981. - 272 p.


[11] Isaenkova M., Perlovich Yu., Fesenko V. Modern methods of experimental construction of texture complete direct pole figures by using X-ray data - IOP Conf. Series: Materials Science and Engineering 130 (2016) 012055 doi:10.1088/1757- 899X/130/1/012055


[12] Isaenkova M., Perlovich Yu. Regularities in the development of crystallographic texture and substructure heterogeneity in zirconium alloys during deformation and heat treatment. - M.: NRNU MEPhI, 2014. - 528 p.


[13] Golovin Yu. Nanoindentation and its capabilities. - Moscow: Mechanical Engineering, 2009. - 312 p.


[14] Grigoryev I. Physical quantities. Handbook, 1991. - 66 c.