KnE Materials Science
ISSN: 2519-1438
The latest conference proceedings on physical materials, energy materials, electrical materials.
Power and Resourse Efficient Envoronmentally Safe Technology for Processing Dumps of Technogenic Waste From Ore-Dressing and Processing Enterprises
Published date: Dec 31 2020
Journal Title: KnE Materials Science
Issue title: IV Congress “Fundamental Research and Applied Developing of Recycling and Utilization Processes of Technogenic Formations” Volume 2020
Pages: 319–325
Authors:
Abstract:
This research proposes a systematic approach for the analysis of volumes, physicochemical, granulometric, lithologic and thermal characteristics of waste from ore-dressing and processing enterprises stored in the dumps (tailing dumps) of ore-dressing and processing plants to assess the economic potential of its use in the system of complex power and resource efficient environmentally safe processing including palletizing machines, conveyor indurating machines and ore–thermal furnaces. The obtained results allow the authors to formulate the basic engineering, technological, economic and environmental requirements for complex chemical and power engineering systems of processing technogenic waste from ore-dressing and processing plants, these results make it also possible to define the degree of variability for the characteristics of the waste lots from various dumps. The paper describes the developed intensional and mathematical formulations for the multiscale problem of optimizing chemical and power engineering processes of technogenic raw materials processing in a complex chemical and power engineering system as a problem for discrete dynamic programming. The distinctive feature of this problem is to take into account the spatio-temporal multistage processing in a moving multilayer mass of pelletized raw material, the intensity of the process of internal moisture transfer and the variables for the control flow of the heat carrier gas. It allows increasing power efficiency by intensifying heat and mass transfer processes of multilayer drying, calcination and sintering. The criterion of the efficiency is the minimum cost of electric and thermal energy spent on processing. The obtained results were used to calculate power efficient environmentally safe processing of technogenic waste from ore-dressing and processing enterprises dumps. It was defined that heat and mass transfer processes are intensified, power consumption is reduced and the quality of the finished product is increased in the conditions of optimal power and resource efficient operation for the processing system.
Keywords: tecnhogenic waste, waste processing, ore-dressing and processing plant, power and resource efficiency, optimization, system analysis, environmentally safety
References:
[1] Bobkov, V. I., et al. (2018). Scientific Basis of Effective Energy Resource Use and Environmentally Safe Processing of Phosphorus-Containing Manufacturing Waste of Ore-Dressing Barrows and Processing Enterprises. Clean Technologies and Environmental Policy, vol. 20, issue 10, pp. 2209-2221.
[2] Bustillo,R.M.(2018).MineralResources:FromExplorationtoSustainabilityAssessment.Cham:Springer Nature, pp. 96-128.
[3] Shvydkii, V. S., et al. (2018). Mathematical Model of Roasting Process of Ore and Coal Pellets in a Indurating Machine. Institution news. Ferrous metallurgy, vol. 60, issue 4, pp. 329 – 335.
[4] Bragin, V. V., et al. (2014). Relation Between the Productivity and Fuel Consumption in Roasting Machines. Steel in translation, vol. 44, issue 8, pp. 590-594.
[5] Meshalkin, V. P., et al. (2017). Computer Modeling of the Chemical-Power Engineering Process of Roasting of a Moving Multilayer Mass of Phosphorite Pellets. Doklady Chemistry, vol. 477, issue 2, pp. 282-285.
[6] Meshalkin, V. P., et al. (2017). Computer-Aided Modeling of the Chemical Process of Drying of a Moving Dense Multilayer Mass of Phosphorite Pellets. Doklady Chemistry, vol. 475(2), рр. 188-191.
[7] Meshalkin, V. P., et al. (2017). Optimizing the Energy Efficiency of the Chemical and Energy Engineering Process of Drying of a Moving Dense Multilayer Mass of Phosphorite Pellets. Doklady Chemistry, vol. 477, issue 2, pp. 286-289.
[8] Akberdin, A. A., Kim, A. S. and Sultangaziev, R. B. (2018). Experiment Planning in the Simulation of Industrial Processes. Steel in translation, vol. 48, issue 9, pp. 573-577.
[9] Akberdin, A. A., Konurov, U. K. and Sultangaziyev, R. B. (2018). Manganese Capacity and Optical Basicity of Metallurgical Slag. Steel in translation, vol. 48, issue 1, pp. 7-10.
[10] Novichikhin, A. V. and Shorokhova, A. V. Systematic Processing of Iron-Ore Waste in Mining Regions. Steel in translation, vol. 47, issue 7, pp. 456-462.
[11] Leontyev, L. I., Grigorovich, K. V. and Kostina, M. V. (2018). Fundamental Research as a Base of Creating New Materials and Technologies in the Field of Metallurgy. Part 1. Institution news. Ferrous metallurgy, vol. 61, issue 1, pp. 11-22.
[12] Gurin, I. A., et al. (2017). Web Technology in Automated Information and Modeling Systems for Metallurgical Processes. Steel in translation, vol. 47, issue 7, pp. 463-468.
[13] Blank, C. E., Parks, R. W. and Hinman, N. W. (2016). Chitin: A Potential New Alternative Nitrogen Source for the Tertiary, Algal-Based Treatment of Pulp and Paper Mill Wastewater. Journal Applied Phycology, vol. 28, issue 5, pp. 2753–2766.
[14] Bokovikov, B. A., Bragin, V. V. and Shvydkii, V. S. (2014). Role of the Thermal-Inertia Zone in Conveyer Roasting Machines. Steel in Translation, vol. 44, issue 8, pp. 595-601.
[15] Nosov, S. K., et al. (2012). Theoretical Basis, Modern Technologies, and Innovations of Ferrous Metallurgy. Russian Metallurgy (Metally), vol. 2012, issue 12, pp. 1007-1013.
[16] Filatov, S. V., et al. (2017) Improving the Energy Efficiency of Blast Furnaces at PAO NLMK. Steel in Translation, vol. 47, issue 8, pp. 534-537.