KnE Engineering

ISSN: 2518-6841

The latest conference proceedings on all fields of engineering.

Stress-strain Relationship in Homogeneous and Two-layered Triaxial Test Specimens

Published date: May 03 2020

Journal Title: KnE Engineering

Issue title: STARTCON19 - International Doctorate Students Conference + Lab Workshop in Civil Engineering

Pages: 88–99

DOI: 10.18502/keg.v5i5.6923

Authors:

Gabriel Oliveira - gabriel.marchi.oliveira@ubi.pt

Isabel Falorca

Abstract:

The stress-strain relationship of a homogeneous specimen, obtained from triaxial compression test, allows to determine stiffness parameters for numerical-method based analyses in common geotechnical software. Stiffness parameters are defined as the ratio of stress to strain along an axis. However, when a heterogeneous specimen is tested, the equivalent elastic modulus that represents a simplification of the nonlinear behavior is complex. This paper presents a study intended to contribute to the debate about the degree to which conventional soil mechanics approaches can be applied to layered specimens. Triaxial compression tests were carried out on both homogeneous and two-layered specimens under a low effective confining pressure of 30 kPa. The triaxial apparatus was chosen since the applied stress and specimen boundary conditions are well defined, and the repeatability of the test method is good. The behavior of both specimens was studied in terms of the stress-strain relationship and stiffness. The main differences were crucial to understanding the composite soil-aggregate interaction, which is discussed and compared. The results indicate that the interface between composite soil and aggregate is important to keep the stability of the layer of aggregate over the soft composite soil, and practical methods of achieving that are suggested.

References:

[1] A. S. Saada, F. C. Townsend, STP740-EB Laboratory Shear Strength of Soil, ASTM International, 7 (1981).

[2] J. T. Germaine, C. C. Ladd, STP977-EB Triaxial Testing of Saturated Cohesive Soils. ASTM International, 421 (1988).

[3] G. Baldi, D. W. Hight, G. E. Thomas, STP977-EB A Re-evaluation of Conventional Triaxial Test Methods, ASTM International, 219 (1988).

[4] P. J. Guo, F.E. Stolle. Lower and upper limits of layered-soil strength, Can. Geotech. J., 46: 665 (2009).

[5] P. J. Guo, F.E. Stolle. A physically meaningful homogenization approach to determine equivalent elastic properties of layered soil, Can. Geotech. J., 55 303 (2018).

[6] J.R.F. Arthur, A. B. Philips, Homogeneous and layered sand in triaxial compression. Géotech., 25 799 (1975).

[7] J.H. Atkinson, Anisotropic elastic deformations in laboratory tests on undisturbed London clay, Géotech. 25, 357, (1975).

[8] R.E. Gibson, The analytical method in soil mechanics, Géotech., 24, 115, (1974).

[9] G. Gazetas, Strip foundations on a cross-anisotropic soil layer subjected to dynamic loading, Géotech., 31, 161, (1981).

[10] J. P. Giroud, J. Han, Design method for geogrid-reinforced unpaved roads. II. Calibration and applications, J. of Geotech. and Geoenv. Eng., 130, 787 (2004).

[11] ASTM D2487, Standard Practice for Classification of Soils for Engineering Purposes, ASTM International (2017).

[12] H.K. Kim, J.C. Santamarina, Sand–rubber mixtures (large rubber chips). Can. Geotech. J., 45, 1457 (2008).

[13] ASTM D4767, Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils, ASTM International (2017).

[14] Y. P. Vaid, S. Sasitharan, The strength and dilatancy of sand, Can. Geotech. J., 29, 522, (1991).

[15] A. Drescher, I. Vardoulakis, Geometric softening in triaxial tests on granular material, Géotech., 39, 291 (1982).

[16] A.W. Bishop, D. J. Henkel, The measurement of soil properties in the triaxial test (Arnould, London, 1962).

[17] P. La Rochelle, S. Leroueil, B. Trak, L. Blais-Leroux, R. Tavenas, STP977-EB Observational Approach to Membrane and Area Corrections in Triaxial Tests, ASTM International (1988).

Download
HTML
Cite
Share
statistics

1671 Abstract Views

385 PDF Downloads